Parts & Accessories

Easily integrated Designed specifically for specific Bontrager Circuit MIPS road bike helmets, the Blendr mount easily integrates Bontrager Ion lights and GoPro cameras. - Quickly mount front light and camera accessories on the front of your Bontrager Circuit MIPS road bike helmet. - Tested with an accelerometer for intended breakaway point if involved in a crash

Add the safety of visibility to your helmet and light up the trail, road, or commute with help from the Bontrager Helmet Mount. Easily attaches a light to most helmets. - Works with all Bontrager Ion and Flare lights

Let's face it - we all sweat. Sweat stinks. Fresh pads will make your helmet smell, and fit, just like it did when it was new. New pads can also help you dial in the perfect fit - keeping you comfortable and looking forward to the next ride. Key features - Original equipment replacement fit pads for your Bontrager Specter helmet - Helmet fit pads should be replaced once a year to maintain fit and hygiene

The ultimate commuter helmet cover combrines a fully reflective fabric, with water and wind protection. - Sugoi's fully reflective and waterproof Zap fabric is designed for high visibility in low light - Two sizes to offer a wider range of fit possibilities

Compatible with Shiner and Shiner Back lights - Rubber pad with loop straps to quickly mount and remove light for recharging - 50mm bolt spacing to fit most rear racks

Taking the ultimate helmet lighting system – the Vis 360 – to the next level, the Vis Pro features an ultra-powerful 600-lumen headlight optimized for commuting and bright enough for twisty singletrack! The featherweight system is waterproof for all-conditions reliability and has an integrated rear light/battery pack that balances the unit on a variety of helmets. An essential setup for those requiring maximum protective visibility with powerful illumination. Featuring: - 600 Lumen Output Certified to the FL-1 Standard - Daylight Visible Pulse Mode - Integrated Battery Pack With Red Rear Lighting - Innovative Amber Sidelights Provides Critical Side Visibility at Intersections - Ultra-lightweight Setup With Easy Clip On/Off Design - Waterproof to 1 meter For All-Conditions Reliability - Accurate Battery Charge & Status Indicator - Micro USB Rechargeable Included: - Helmet Mounts & Micro USB Charging Cable

A helmet-mounted taillight is an ideal way to help make sure you are seen in low light conditions. The ATS LED Taillight only fits Lazer helmets equipped with the Advanced Turnfit System. - COMPATIBILITY: Bullet 2.0, Century MIPS, Century, Wasp Air Tri, Victor, Impala MIPS, Impala, Urbanize MIPS - BATTERY TYPE: LR41 button battery - RUN TIME: 37 hours - LUMENS: 4 lumens - ATTACHMENT: ATS dial - WEIGHT: 15g - MATERIAL: Nylon

Keep the rain, snow and mud from getting inside your helmet, or use as a quick aerodynamic solution to close off the front and side vents. Aeroshell is a great accessory for compatible Lazer helmets! The Aeroshell is a plastic cover, designed to fit perfectly over specific models of Lazer helmets. The Aeroshell snaps into place and protects the riders head from wind and rain while still allowing for some air movement under the front of the helmet and out the rear vents. The Aeroshell is unique in that it is easily removed from the helmet when riding conditions are such that additional ventilation is desired. Snap it on when the rain is pouring down and pull it off when the sun starts to shine, the Aeroshell is the perfect tool for every possible condition. Additionally, the Aeroshell provides a significant increase in Aerodynamic performance once it is installed on the helmet. By closing off the ventilation holes, the amount of aerodynamic drag the helmet creates is strongly reduced, making your road helmet into an aero helmet and resulting in a faster ride. - COMPATIBILITY: Blade+ MIPS, Blade+, Blade, Blade MIPS - ATTACHMENT: Blade or Blade+ helmet - WEIGHT: 45g - MATERIAL: Polycarbonate

Keep the rain, snow and mud from getting inside your helmet, or use as a quick aerodynamic solution to close off the front and side vents. Aeroshell is a great accessory for compatible Lazer helmets! The Aeroshell is a plastic cover, designed to fit perfectly over specific models of Lazer helmets. The Aeroshell snaps into place and protects the riders head from wind and rain while still allowing for some air movement under the front of the helmet and out the rear vents. The Aeroshell is unique in that it is easily removed from the helmet when riding conditions are such that additional ventilation is desired. Snap it on when the rain is pouring down and pull it off when the sun starts to shine, the Aeroshell is the perfect tool for every possible condition. Additionally, the Aeroshell provides a significant increase in Aerodynamic performance once it is installed on the helmet. By closing off the ventilation holes, the amount of aerodynamic drag the helmet creates is strongly reduced, making your road helmet into an aero helmet and resulting in a faster ride. - COMPATIBILITY: G1 MIPS, G1 - ATTACHMENT: G1 helmet - WEIGHT: 45g - MATERIAL: Polycarbonate

Keep the rain, snow and mud from getting inside your helmet, or use as a quick aerodynamic solution to close off the front and side vents. Aeroshell is a great accessory for compatible Lazer helmets! The Aeroshell is a plastic cover, designed to fit perfectly over specific models of Lazer helmets. The Aeroshell snaps into place and protects the riders head from wind and rain while still allowing for some air movement under the front of the helmet and out the rear vents. The Aeroshell is unique in that it is easily removed from the helmet when riding conditions are such that additional ventilation is desired. Snap it on when the rain is pouring down and pull it off when the sun starts to shine, the Aeroshell is the perfect tool for every possible condition. Additionally the Aeroshell provides a significant increase in Aerodynamic performance once it is installed on the helmet. By closing off the ventilation holes, the amount of aerodynamic drag the helmet creates is strongly reduced, making your road helmet into an aero helmet and resulting in a faster ride. Sizing: - Small = 52 – 56cm - Medium = 55 – 59cm - Large = 58 – 61cm

Keep the rain, snow and mud from getting inside your helmet, or use as a quick aerodynamic solution to close off the front and side vents. Aeroshell is a great accessory for compatible Lazer helmets! The Aeroshell is a plastic cover, designed to fit perfectly over specific models of Lazer helmets. The Aeroshell snaps into place and protects the riders head from wind and rain while still allowing for some air movement under the front of the helmet and out the rear vents. The Aeroshell is unique in that it is easily removed from the helmet when riding conditions are such that additional ventilation is desired. Snap it on when the rain is pouring down and pull it off when the sun starts to shine, the Aeroshell is the perfect tool for every possible condition. Additionally the Aeroshell provides a significant increase in Aerodynamic performance once it is installed on the helmet. By closing off the ventilation holes, the amount of aerodynamic drag the helmet creates is strongly reduced, making your road helmet into an aero helmet and resulting in a faster ride.

Keep the rain, snow and mud from getting inside your helmet, or use as a quick aerodynamic solution to close off the front and side vents. Aeroshell is a great accessory for compatible Lazer helmets! The Aeroshell is a plastic cover, designed to fit perfectly over specific models of Lazer helmets. The Aeroshell snaps into place and protects the riders head from wind and rain while still allowing for some air movement under the front of the helmet and out the rear vents. The Aeroshell is unique in that it is easily removed from the helmet when riding conditions are such that additional ventilation is desired. Snap it on when the rain is pouring down and pull it off when the sun starts to shine, the Aeroshell is the perfect tool for every possible condition. Additionally, the Aeroshell provides a significant increase in Aerodynamic performance once it is installed on the helmet. By closing off the ventilation holes, the amount of aerodynamic drag the helmet creates is strongly reduced, making your road helmet into an aero helmet and resulting in a faster ride. - COMPATIBILITY: Z1 MIPS, Z1 - ATTACHMENT: Z1 helmet - WEIGHT: 45g - MATERIAL: Polycarbonate

Replacement Pads for Lazer's BOB Helmet

A user adjutable cap for the Bullet 2.0 in order to provide airflow or maximize aerodynamics. - COMPATIBILITY: Bullet 2.0 - ATTACHMENT: Bullet 2.0 helmet - WEIGHT: 34g - MATERIAL: Polycarbonate

A closed cap for the Bullet 2.0 in order to block airflow and maximize aerodynamics. - COMPATIBILITY: Bullet 2.0 - ATTACHMENT: Bullet vent - WEIGHT: 21g - MATERIAL: Polycarbonate

Magnetic mount lens for Lazer Bullet 2.0 helmet. The integrated lens is an integral part of the Bullet 2.0 helmet. It can be stored on the helmet surface using the magnetic docking when not in use. - COMPATIBILITY: Bullet 2.0 - ATTACHMENT: magnetic - WEIGHT: 24g - MATERIAL: Polycarbonate

Venturi technology accelerates the airflow through the helmet. By creating an active air draw at the rear of the helmet, the Venturi cap increases airflow through the Lazer Bullet 2.0. - COMPATIBILITY: Bullet 2.0 - ATTACHMENT: Bullet 2.0 helmet - WEIGHT: 21g - MATERIAL: Polycarbonate

Freshen up the interior of your helmet with a new pad set! Padset details listed below. Replacement padset for Lazer Bullet and Bullet MIPS helmets. Set includes six pads - Two front pads, two top center pads, two top side pads. - COMPATIBILITY: Bullet, Bullet 2.0 - ATTACHMENT: velcro - WEIGHT: 12g - MATERIAL: Foam

A helmet-mounted taillight is an ideal way to help make sure you are seen in low light conditions. - COMPATIBILITY: Cameleon MIPS - RECHARGE TIME: 2 hours - RUN TIME: 24 hours - LUMENS: 5.2 lumens - ATTACHMENT: Rear vent - WEIGHT: 19g - MATERIAL: LED light

A helmet-mounted taillight is an ideal way to help make sure you are seen in low light conditions. - COMPATIBILITY: Gekko MIPS, Gekko, Lil'Gekko MIPS, Lil'Gekko - BATTERY TYPE: USB rechargeable - RECHARGE TIME: 2 hours - RUN TIME: 24 hours - LUMENS: 5.2 lumens - ATTACHMENT: Rear vent - WEIGHT: 19g - MATERIAL: LED light

Screws for Impala visor. - COMPATIBILITY: Impala MIPS, Impala - WEIGHT: 1g - MATERIAL: Aluminum

Camera mount for Jackal and Impala helmets. - COMPATIBILITY: Jackal MIPS, Jackal, Impala MIPS, Impala - ATTACHMENT: Velcro - WEIGHT: 13g - MATERIAL: Nylon

Keep the ARS fit system clear of debris and serves as a mount for LED taillight accessory. Note: not compatible with LifeBeam accessory. Adds protection to keep ARS retention system clear of debris on Z1 helmet. Also allows the Z-LED or Century LED taillights to be used with the Z1 helmet. - COMPATIBILITY: Z1 - ATTACHMENT: ARS mechanism - WEIGHT: 8g - MATERIAL: Polycarbonate

Freshen up the interior of your helmet with a new pad set! Padset details listed below. Replacement padset for Lazer Bullet and Bullet MIPS helmets. Set includes six pads - Two front pads, two top center pads, two top side pads. - COMPATIBILITY: Bullet, Bullet 2.0 - ATTACHMENT: velcro - WEIGHT: 12g - MATERIAL: Foam

Freshen up the interior of your helmet with a new pad set! Padset details listed below. Replacement padset for Lazer Cameleon MIPS helmet. Set includes four pads - front pad, two top side pads and top center pad. - COMPATIBILITY: Cameleon MIPS - ATTACHMENT: velcro - WEIGHT: 12g - MATERIAL: Foam

Freshen up the interior of your helmet with a new pad set! Padset details listed below. Replacement padset for Lazer G1 and G1 MIPS helmets. This is the standard padset. Set includes four pads - front pad, two top side pads and one top center pad. - COMPATIBILITY: G1 MIPS, G1 - ATTACHMENT: velcro - WEIGHT: 12g - MATERIAL: Foam

Freshen up the interior of your helmet with a new pad set! Padset details listed below. Replacement padset for Lazer Impala and Impala MIPS helmets. Set includes three pads - One front/top pad and two top side pads. - COMPATIBILITY: Impala MIPS, Impala - ATTACHMENT: velcro - WEIGHT: 12g - MATERIAL: Foam

Freshen up the interior of your helmet with a new pad set! Padset details listed below. Replacement padset for Lazer Jackal MIPS helmets. Set includes one pad - Front/Top unipad only. - COMPATIBILITY: Jackal MIPS, Jackal - ATTACHMENT: velcro - WEIGHT: 12g - MATERIAL: Foam

Freshen up the interior of your helmet with a new pad set! - Replacement pads for Jackal helmets

Freshen up the interior of your helmet with a new pad set! - Replacement pads for Sphere helmets - Attachment: Velcro - Material: Foam